A two component repair and rebuilding material based on a ceramic steel reinforced polymer system. Super Metal does not require any special tools to apply. It will bond to almost any surface and can be machined using conventional tools.

Two component paste grade repair and rebuilding material with an extended working life that provides greater time for mixing and application. Based on a ceramic steel reinforced polymer system, it is designed for applications where accurate alignment or placement of large volumes of material is required.

A two component paste grade system based on a silicon steel alloy blended with graphite and high molecular weight reactive polymers and oligomers. When cured, the material is fully machinable and possesses self lubricating properties and porosity. For use on low friction surfaces subject to intermittent contact where specific loads are low.

Repair system designed for rebuilding shallow pitting in metals damaged by erosion-corrosion.

A two component paste grade repair system. Rapid curing and a high level of tolerance to surface contamination – ideally suited where grit blasting can not be achieved and when surface preparation is minimal or if substrate is heaviliy contaminated with oil or water.

A rapidly solidifying repair system for emergency and permanent bondings, repairing or rebuilding of all ferrous and non-ferrous metals. 1221 is urethane based technology.

A single component paste grade system based on a silicon steel alloy blended with a heat activated resin. When cured, the material is durable and corrosion resistant. Designed to be applied to hot surfaces 158-302ºF.

A two component, non-machinable grade material based on a silicon steel alloy blended with high molecular weight reactive polymers and oligomers. The system is designed for rebuilding metals and offers protection against the effects of erosion-corrosion. Ideally suited to be overcoated with Belzona 1321.

Two-component solvent free sprayable coating system designed to operate under continuous immersion at temperatures up to 122⁰F, Will not shrink, expand or distort – has up to 24 hour ovecoat window.

A two component, drinking water certified coating system for improving the efficiency of fluid handling systems and protecting metals from the effects of erosion-corrosion.

A two-component fluid grade system for protecting immersed surfaces suffering from erosion-corrosion at operating temperatures up to 140 °F (60 °C), for improving the efficiency of fluid handling equipment, for structural bonding, and for creating irregular load bearing shims with good electrical insulation properties.

Two-component solvent free sprayable coating system designed to operate under continuous immersion at temperatures up to 203⁰F, Will not shrink, expand or distort – has up to 24 hour ovecoat window. Two (2) coats recommended.

Coating system for high temperature equipment handling water and aqueous solutions. Also used as a high strength structural adhesive for bonding or for creation of irregular load bearing shims with good electrical insulation characteristics. Technical formulation.

A two-component high temperature coating systems designed to resist water and pressurized steam up to a temperature of 248°F and to exhibit excellent erosion-corrosion resistance at elevated temperatures.

High temperature repair system designed for rebuilding metals damaged by erosion-corrosion.

Two-component, spray applied, high temperature coating suitable for continuous immersion in aqueous/hydrocarbon systems up to 284⁰F. Also suitable for steaming out up to 410⁰F.

Coating for repairing and protecting surfaces against abrasive attack. A slightly more flexible system, offering better impact protection. Has a greater slump resistance, so can be built up in thicker layers (up to 1″) on vertical/overhead areas. Generally better protection for large particles (stones, rocks).

Coating for repairing and protecting surfaces against abrasive attack. Generally better heat resistance and slightly better chemical resistance than 1811. Generally better protection for fine particles (powders). Offers faster cure than 1811, if downtime is an issue.

Two-component repair and protective coating for surfaces subject to abrasive attack at elevated temperatures (up to 200⁰F) and is resistant to a wide range of chemicals. Will not shrink, distort or expand and does not corrode.

Three-component repair system for protecting large surface application areas subject to abrasive attack. 1814 can withstand dry abrasion up to 158F and bond to all rigid sutstrates.

Is a fluid grade grip system used to bond Belzona 9211 and Belzona 9231 to the surface of machinery and equipment. Is solvent free and low odor and is durable, with excellent adhesion, wear and chemical resistance.

SuperWrap II – Winter Grade – designed for colder climates, can be applied between 41F and 68F. Once cured, it resists temperatures up to 140F.

SuperWrap II – Tropical Grade – designed for applications in higher ambient temperatures, can be applied between 68F and 104F. Once cured, it resists temperatures up to 176F.

SuperWrap II – High Temp – designed for applications in higher ambient temperatures, can be applied between 41F and 104F. Once cured, it resists temperatures up to 302F.